Workshops and warehouses, kept running
Mechanical workshops, panel shops and light industrial. Three-phase machinery, hoists, compressors, lighting and the maintenance that stops the breakdown happening in the first place.
Tell us about the site
Breakdowns get a call back first. Everything else, a quote usually within the day.
No call centre. Goes straight to us.
Machine down? Board tripped?
A workshop with no power isn't earning. Ring us — breakdowns get priority over quoted work.
The work that keeps a workshop open
We're not chasing retail fit-outs or high-rise strata. This is machinery, power and lighting for businesses that make or fix things.
Three-phase machinery
New circuits and outlets for lathes, presses, welders and plant. Correctly rated protection, isolation within reach, and cable sized for the actual load.
Hoists and compressors
Two-post and four-post hoists, compressor circuits, emergency stops and isolators. Installed, connected, commissioned and certified.
Lighting upgrades
High-bay and LED replacements that cut the bill and let people actually see what they're working on. Usually the fastest payback on the site.
Switchboards & distribution
Main switchboards, subboards, and capacity for the next machine. Labelled so the next person doesn't have to guess.
Test and tag, RCD testing
Scheduled testing with a register that satisfies an auditor or insurer. Booked in so you're not scrambling when it's due.
Breakdowns
Something's stopped and nobody's earning. Fault traced, fixed if we can on the spot, and honest about it if a part's needed.
Recent work
Workshop power and lighting across Pakenham, Officer and the surrounding industrial estates.
Plant that has to run tomorrow morning
Conveyors, graders, washers and the gear that drives them. Wet floors, constant washdown and a production schedule that doesn't care when a motor lets go.
Isolation you can actually reach
A local isolator at the machine, labelled to the circuit it kills, is the difference between a five-minute clean-out and someone walking back to the switchboard guessing. It's also what an auditor looks for first.
Motors and drives
Gearmotors, conveyor drives and VSDs — swapped out, wired, rotation checked and run up before we leave. Washdown kills terminal boxes and glands long before it kills the motor, so we replace what's gone rather than re-landing wires into a corroded box.
Built around your downtime, not ours
Commercial work has a cost every hour the site isn't running. We price and schedule with that in mind.
- After-hours and weekends where the work would stop production
- Breakdowns jump the queue — quoted work can wait, a stopped machine can't
- One point of contact — the person who quoted it does it
- Account terms available for regular maintenance clients
- Documentation that stands up — certificates, test registers, board schedules
- Scheduled maintenance so the next breakdown doesn't happen
Who we're a good fit for
- Mechanical workshops and service centres
- Panel and paint shops
- Fabrication and light manufacturing
- Warehouses and storage facilities
- Trade and equipment hire businesses
- Small industrial estate tenancies
Running a fleet or putting chargers in for staff and customers? Commercial EV charging is the same conversation — load assessment first, hardware second.
Three steps, no surprises
Call or send the form
Tell us the site and what's needed. Breakdowns get a call back first.
Site visit and fixed price
We look at the board and the load, then quote properly. Scheduled around your operating hours.
Done, tested, documented
Certificate of Electrical Safety, updated board schedule, and a test register if it applies.
Questions we get asked
Do you do after-hours work?
Where the job would otherwise stop production, yes. Changeovers, board work and machinery circuits can be scheduled outside operating hours by arrangement. It costs more per hour and usually less overall.
Can you connect imported machinery?
Usually. Imported plant often arrives wired for a different supply voltage or frequency, or without isolation that meets Australian requirements. We assess it, sort the connection and isolation properly, and certify the installation work — the machine's own internals remain the manufacturer's responsibility.
Do you do test and tag?
Yes, along with RCD testing and scheduled maintenance, with a register you can hand straight to an auditor or insurer. We'll set the interval based on your environment rather than defaulting to the shortest one.
How quickly can you get to a breakdown?
In the core area — Pakenham, Officer, Beaconsfield, Berwick, Narre Warren, Cardinia — usually same day. Breakdowns take priority over quoted work, because a stopped site is costing you more than the call-out.
Do you offer account terms?
For regular maintenance clients, yes. Ring and we'll sort it out rather than making you fill in a form for a one-off job.
Will an LED lighting upgrade actually save money?
In a workshop running long hours on old high-bay fittings, usually yes, and often the payback is short enough to be obvious. We'll count the fittings, work out the running hours and show you the numbers before you commit rather than quoting a percentage off a brochure.
Where we work
Based in Pakenham. Commercial work is worth travelling further for than a small service call.
Core — same or next day
- Pakenham
- Officer
- Beaconsfield
- Berwick
- Narre Warren
- Cardinia
Regular — usually within the week
- Cranbourne
- Clyde & Clyde North
- Drouin
- Warragul
- Emerald & Cockatoo
- Hallam
By arrangement
- Dandenong
- Frankston
- Phillip Island
Get the site sorted
Tell us where you are and what's needed. Breakdowns get a call back first.